AC Zincs Corrosion Grenade 1 1/8" Clamp-On Zinc Sacrificial Anode, ACZ-1 1/8
The AC Zincs Corrosion Grenade ACZ-1 1/8 is the largest zinc anode in the Corrosion Grenade lineup, built for 1 1/8" copper suction lines on larger air conditioning and refrigeration equipment. Clamped to the suction line, it gives galvanic corrosion a softer target than the outdoor coil's aluminum fins, helping protect expensive equipment from salt-air damage. Manufacturer AC Zincs of Largo, Florida calls it a truly green solution: a simple metal anode instead of chemicals or coil replacement.
Is the 1 1/8" Corrosion Grenade the Right Size?
The ACZ-1 1/8 fits a 1 1/8" OD copper suction line, the largest size AC Zincs offers. It's suited to larger residential and commercial condensing units and refrigeration equipment with bigger suction lines. Measure the line at the outdoor unit to confirm.
Commercial rooftop and ground-level equipment near the coast can lose coil fins quickly, which drives up energy use and repair costs. If you're running new line, our Mueller 1 1/8" American-made copper line is available in 50 ft coils.
Ideal for: Larger coastal AC and refrigeration systems with 1 1/8" suction lines, including commercial and multi-family equipment.
Need a smaller size? The AC Zincs Corrosion Grenade 7/8" ACZ-7/8 fits 7/8" suction lines.
Size the Corrosion Grenade to the measured outside diameter of the suction line. Results vary with environment, exposure and maintenance. Request product assistance, contact Budget Heating, or call 813-885-7999.
What's Included
| Product | AC Zincs Corrosion Grenade — ACZ-1 1/8 |
|---|---|
| Line Size | Fits 1 1/8" OD Copper Suction Line |
| Anode Material | Zinc Alloy Sacrificial Anode |
| Design | Two-Piece Clamp-On With Stainless Steel Bolts |
| Mounting Location | Compressor Suction Line, Where It Typically Remains Wet |
| Protects | Outdoor Coil Aluminum Fins From Galvanic Corrosion |
| Application | Larger Air Conditioning and Refrigeration Systems Near the Coast |
| Manufacturing Standard | Manufactured to Strict U.S. Military Specifications |
The ACZ-1 1/8 is the top size in AC Zincs' zinc Corrosion Grenade range (3/8" through 1 1/8"). It uses the same two-piece clamp-on body and stainless steel bolts, with mass matched to a 1 1/8" line. Clean the copper to bare metal, clamp the halves around the wet section of the suction line, and the anode starts working immediately.
How It Works & Installation Features
ACZ-1 1/8 Corrosion Protection
- Largest zinc Corrosion Grenade size
- Sacrificial anode for 1 1/8" suction lines
- Diverts galvanic corrosion from aluminum coil fins
- Helps protect larger, costlier coils
- Helps maintain efficiency on commercial equipment
- Protection begins on installation
- Several years of protection
- Manufactured to strict U.S. military specifications
- A green, chemical-free approach, per the manufacturer
- Works with existing coil cleaning and coating programs
ACZ-1 1/8 Installation & Maintenance
- Clamp-on body for 1 1/8" OD copper
- Two halves separate with an Allen wrench
- Stainless steel fastening bolts
- Sand cloth the line to bare copper
- Clear labels and coatings from the contact area
- Install where the suction line stays wet
- Correct size and weight to prevent vibration
- No brazing or refrigerant recovery needed
- Replace when the anode loosens from wear
- Easy to add to commercial maintenance routes
Specifications & Manuals
The Corrosion Grenade brochure explains galvanic corrosion in AC systems, how sacrificial anodes protect aluminum fins, and the available sizes.
Frequently Asked Questions
Is 1 1/8" the largest Corrosion Grenade available?
Yes. AC Zincs makes the zinc Corrosion Grenade in 3/8", 1/2", 5/8", 3/4", 7/8" and 1 1/8" sizes, and the ACZ-1 1/8 is the largest.
Does the Corrosion Grenade need power or wiring?
No. It's a clamp-on metal anode. Installation consists of cleaning the copper line, clamping on the two halves and tightening the stainless steel bolts.
Why does AC Zincs call the Corrosion Grenade a green solution?
AC Zincs describes it as a truly green solution because it adapts a proven marine sacrificial-anode method to extend coil life, reducing the need for early coil or equipment replacement.
Who makes the Corrosion Grenade?
The Corrosion Grenade is made by A/C Zincs, Inc., based in Largo, Florida, and manufactured to strict U.S. military specifications.
How should the 1 1/8" anode be positioned on a large condensing unit?
Clamp it to the compressor suction line at the outdoor unit, at a spot where the line typically stays wet, on bare copper free of labels and coatings.
Who typically buys the 1 1/8" Corrosion Grenade?
Commercial HVAC and refrigeration contractors, property managers of coastal multi-family and commercial buildings, and owners of larger systems near salt water.

Corrosion Grenade Borchure