2.5 Ton EcoTemp 13.4 SEER2 R-454B 60K BTU Gas Package Unit WPG530A060RKB
Many homes fall between 2 and 3 tons, and the EcoTemp WPG530A060RKB is built for that middle ground. This 2.5 ton single-packaged unit delivers 28,800 BTUh of rated cooling and 950 CFM of standard airflow at 13.4 SEER2. Its 60,000 BTU input furnace supplies 49,000 BTU of heat output at 81% AFUE. Everything is factory charged with R-454B and sealed in a corrosion-resistant cabinet. It suits mid-size homes, manufactured homes, and light commercial spaces that outgrew a 2 ton unit but would be oversized by a 3 ton. Browse the full lineup of package, mobile home, and rooftop units to compare.
Is a 2.5 Ton Gas Package Unit the Right Size?
An oversized air conditioner cools a room quickly but shuts off before it removes enough humidity, which leaves the space cool and clammy. An undersized unit runs nonstop on the hottest afternoons. The half-ton step of the WPG530A060RKB lets you match the calculated cooling load more closely. It adds about 5,600 BTUh of rated cooling and 200 CFM over the 2 ton models.
Sun exposure, ceiling height, occupancy, kitchen heat, and duct condition all affect where your home lands. A load calculation that shows about 27,000 to 30,000 BTUh of heat gain is the typical case for a 2.5 ton unit. On the heating side, 49,000 BTU of output covers many mid-size homes in moderate climates.
Ideal for: Mid-size single-family homes, double-wide manufactured homes, small retail spaces, and professional offices with cooling loads between 2 and 3 tons.
Need more capacity? Step up to the 3 Ton EcoTemp 60K BTU Gas Package Unit WPG536A060RKB for an additional half ton of cooling.
Recommended applications are general guidelines only. Actual system requirements depend on insulation, ductwork, climate, window area, occupancy, and a proper load calculation. Request free sizing assistance, contact Budget Heating, or call 813-885-7999.
What's Included
| Package Unit | WPG530A060RKB: 2.5 Ton Single-Packaged Air Conditioner & Gas Furnace |
|---|---|
| Cooling Capacity | 28,800 BTUh Rated (30,000 BTUh Nominal), 950 CFM |
| Gas Heating | 60,000 BTU Input / 49,000 BTU Output, 81% AFUE |
| Efficiency | 13.4 SEER2 / 11.05 EER2 |
| Refrigerant | R-454B, Factory Charged (4.85 lb), with Leak Detection Dissipation System |
| Compressor | Scroll Compressor |
| Airflow Configuration | Convertible Downflow or Horizontal, Insulated Horizontal Duct Covers Included |
| Electrical | 208/230V, Single Phase, 60 Hz; 20.6 MCA, 30 Amp Max Fuse/Breaker |
At about 348 lb shipped, the WPG530A060RKB is only 9 lb heavier than the 2 ton models, so it handles just as easily on a pad or roof curb. It requires a 30 amp maximum breaker instead of 20 amps. Confirm your existing circuit before swapping out a smaller unit. The R-454B charge, filter driers, and refrigerant service connections are all factory installed. Learn why the industry moved to this refrigerant in our refrigerant transition guide.
Cooling & Gas Heating Features
WPG530A060RKB Air Conditioning Section
- 28,800 BTUh rated cooling bridges the gap between 2 and 3 tons
- 950 CFM standard airflow from an ECM indoor blower
- 13.4 SEER2 and 11.05 EER2 efficiency ratings
- Hermetic scroll compressor with high-pressure switch protection
- R-454B refrigerant with factory leak detection and dissipation
- 1/5 HP direct-drive outdoor fan motor
- Larger 13.6 sq ft outdoor coil face area than the 2 ton models
- Time Guard II anti-short-cycle circuitry
- Indoor coil protected inside the insulated cabinet
- 73 dBA rated sound level
WPG530A060RKB Gas Furnace Section
- 60,000 BTU input / 49,000 BTU output gas heat
- 81% AFUE annual fuel utilization efficiency
- Direct spark ignition with no standing pilot
- Monoport inshot burners for clean, even combustion
- Corrosion-resistant stainless steel Turbo-tubular heat exchanger
- Integrated Gas Control board with fault diagnostics
- Field-installed propane conversion kit available
- 25–55°F temperature rise range
- 90-second blower off-delay captures residual heat
- Single-compartment access to all gas components
Specifications & Manuals
Product documentation includes WPG5 technical specifications, performance and electrical data, installation instructions, the product brochure, and EcoTemp warranty terms to assist with equipment selection, installation, and service.
Frequently Asked Questions
What does stepping up to 2.5 tons get me over the 2 ton 60K model?
The WPG530A060RKB raises rated cooling from 23,200 to 28,800 BTUh and airflow from 750 to 950 CFM, while keeping the same 60K BTU furnace. It needs a larger circuit: 20.6 MCA with a 30 amp maximum breaker.
How loud is the WPG530A060RKB?
The manufacturer rates the A-weighted sound power level at 73 dBA. The draw-through condenser design discharges air vertically to help keep sound levels down.
Which roof curb fits the WPG530A060RKB?
The manufacturer lists the 14-inch roof curb CPRFCURB011B00 for sizes 24–30, and the adapter curb CPADCURB001A00 for the same sizes. A basepan nesting feature helps the unit seal to the curb.
How much R-454B refrigerant is in the WPG530A060RKB?
The unit leaves the factory with about 4.85 lb of R-454B already charged. With properly sized lines and no field piping, it is ready to commission once installed.
Is the WPG530A060RKB suitable for light commercial use?
Yes. The WPG5 series is designed for residential and light commercial applications, and the 2.5 ton size is a common fit for small offices and storefronts on single-phase power.
What breaker size does the WPG530A060RKB require?
Use a maximum 30 amp fuse or HACR breaker, with conductors sized for a minimum circuit ampacity of 20.6 amps on 208/230V single-phase power, per local code.
WPG5 Technical Specifications
WPG5 Installation ManualWPG5 Product Brochure
WPG5 Warranty
